Izvijač križni (PH) TBI, za siguran rad na visini
Tehnički podaci
pdfIzvijač križni (PH) TBI, za siguran rad na visini - 615TBI-H
Više o proizvodu
Profili
Atributi proizvoda
- vrh od krom-vanadij-molibdena, u cjelosti ojačan i zakaljen
- tijelo kromirano, vrh bruniran
- ručka ergonomski oblikovana
- trokomponentni materijal
- otvor u dršci za vješanje
- izrađeno prema standardu ISO8764-1,2
Prednosti:
- Rotirajuća metalna kopča je ergonomski oblikovana i sprječava da traka za pričvršćivanje bude namotana.
- na svakom je alatu označena težina alata
- dvije kopče mogu se učvrstiti u kopču, što osigurava sigurnu promjenu alata
- Unior je prilagođen za rad na visini i održava osnovne funkcije alata
Upotreba (slike)
The carabiner on the lanyard is attached to the ring on the tool. The rings on the tools are large enough to accept 2 carabiners.
The carabiner on the lanyard has to be protected against opening using a lock ring.
Before removing the tool from the belt, unscrew the lock ring on the carabiner on the belt.
Open the carabiner on the belt and remove the tool, which is attached to a lanyard, from the carabiner on the belt. The tool is now ready for use.
Correct attachment of the tool to the lanyard. Return the tool to the belt following the steps in reverse order.
Using the socket remover (Article 1111) depress the pin in the hole while removing the socket from the square drive of the ratchet and then switch the socket or extension.
Safety tips
- Use a screw holding screwdriver to get screws started in awkward, hard-to-reach areas.
- Use a stubby screwdriver in close quarters where a conventional screwdriver cannot be used.
- A rounded tip should be redressed with a file; make sure edges are straight.
- Screwdrivers used in the shop are best stored in a rack. This way, the proper selection of the right screwdriver can be quickly made.
- Keep the screwdriver handle clean; a greasy handle is apt to cause accidents.
- A screwdriver should never be used as pry bar. If it is overstressed in this manner, the blade might break and send a particle of steel into the operator's arm or even towards his eyes.
- Always change tools in secure areas where there is no risk of falling tools.
- Always use tools with Unior carabiners and never use carabiners with a diameter less than 6mm.
- Tools being used at height should regularly be checked for damage and that there is no damage to lanyards, carabiners, attachment rings or belts.
- Don't use pliers on the handle of a screwdriver to get extra turning power. A wrench should only be used on the square shank or bolster of a screwdriver that is especially designed for that purpose.
- Don't expose a screwdriver blade to excessive heat as it may reduce the hardness of the blade.
- Don't use a screwdriver with a split or broken handle.
- Don't use a regular screwdriver to check a storage battery or to determine if an electrical circuit is live.
- Don't use tools without attaching them to your work belt when working at height.
- Don't use and fix damaged tools.
- Don't exceed maximum weight of 2.3kg for individual tools that a worker can attach to their belt.
Safety (slike)
User must be trained to perform work at heights pursuant to the national legislation.
User must use the prescribed personal protective equipment.
Working range at heights is the radius of two metres from the point of attachment on the user. No other person or equipment is permitted within that range due to the possibility of damage caused by a falling tool.
Please check the tools regularly and always before each use.
Poslije svakog ispadanja alata, provjerite stanje konopca i alata. ako je potrebno zamijenite konopac i/ili alat.
The maximum weight of each tool defined by Unior as safe tool for work at heights attached to a work belt amounts to 2.3kg.
The total weight of tools that can be attached to a user's work belt should not exceed 10% of the user's weight.
Attachment ropes should not be shortened, reworked etc. If a rope is damaged or destroyed, do not use the tools.
During work, do not unfasten or detach tools from yourself.
When changing (switching) tools, it is recommended to observe the procedure of replacement described in the Unior d.d. catalogue (tools are attached throughout the replacement with one carabiner or the replacement is made at a so-called safe place).
Do not drop or throw tools deliberately, since this may result in a spring effect and unforeseen consequences.
Tools on a rope should not be wound, since that may lead to unforeseen consequences.
User selects Unior attachment elements depending on the purpose of use and with respect to the weight of tools (tool weight is indicated on a tool).
Tracking manufacture code and final control code are indicated on each tool.
Questions & Answers
-
Can we use a tool for working at height as a normal tool?A tool for working at height has the same usability as a normal tool, except that a non-removable riveted metal buckle is added to this tool.
-
Does the stated weight per tool for safe work at height also include the weight of the metal ring?The weight of the tool marked on the tool, included also weight of metal ring
VELIKO EFIKASNA REŠENJA
Rad na visini podrazumeva visok nivo rizika, tako da se ništa ne može prepustiti slučaju. Unior - sinonim za visokokvalitetne ručne alate, predstavlja liniju alata posebno prilagođenih za rad na visini kako bi se izbjegli opasni padovi.KVALITETNI ALATI ZA SIGURAN RAD NA VISINAMA
Alat za visinu rada standardni je alat s nadogradnjom - mogućnost priveza. Povezani alat značajno poboljšava sigurnost posla.Visoka preciznost
Uniorovi alati za rad na visini su dizajnirani da sačuvaju osnovne funkcije alata, ergonomiju i korisnost, ili da ih smanje u najmanjoj mogućoj meri.