İç segman pensesi, düz, yüksekliklerde güvenli çalışma için

Product features

  • malzeme: özel alet çeliği
  • sıcak dövme, tamamen sertleştirilmiş ve temperlenmiş
  • başlık cilalıdır
  • yüzey bitirme: ISO 1456:2009 standardına göre krom kaplamalı
  • uçlar siyah bitirmedir
  • çift plastik daldırma kol
  • DIN 5256 standardı C formuna göre yapılmıştır

Avantajları:

  • En yüksek güvenlik seviyesini sağlamak için perçinlenmiş metal halka yalnızca plastik kollara monte edilmez, aynı zamanda alet kolunun metal kısmına tutturulur.
  • çıkarılamayan perçinli metal halka
  • takım ağırlığı her takımın üzerinde işaretlenmiştir
  • aletlerin üzerindeki halkalar 2 karabinayı alacak kadar büyüktür
  • Unior’un yükseklikte çalışma aletleri, araçların temel işlevlerini, ergonomisini ve kullanışlılığını korumak veya bunları mümkün olan en küçük ölçüde azaltmak için tasarlanmıştır.
  • pratik segman penselerine kıyasla %30 daha yüksek dayanıklılık
  • takılı uçlarla birlikte
  • 8 ilâ 100mm arası çap için

Kullanım:

  • segmanları millere takmak için
#title#
kodLenghtMil çapı için DIN 472 ve DIN 984'e göre segmanlar içinDiameterAdditionsl lenghtağırlık
62638718019 - 601,852189
* Ürünlerin resimleri semboliktir. Bütün boyutlar mm ve ağırlık gram cinsindendir.

Kullanım (pictures)

The carabiner on the lanyard is attached to the ring on the tool. The rings on the tools are large enough to accept 2 carabiners.

The carabiner on the lanyard has to be protected against opening using a lock ring.

Before removing the tool from the belt, unscrew the lock ring on the carabiner on the belt.

Open the carabiner on the belt and remove the tool, which is attached to a lanyard, from the carabiner on the belt. The tool is now ready for use.

Correct attachment of the tool to the lanyard. Return the tool to the belt following the steps in reverse order.

Using the socket remover (Article 1111) depress the pin in the hole while removing the socket from the square drive of the ratchet and then switch the socket or extension.

Safety tips

check-mark-yes.png
  • Always change tools in secure areas where there is no risk of falling tools.
  • Always use tools with Unior carabiners and never use carabiners with a diameter less than 6mm.
  • Tools being used at height should regularly be checked for damage and that there is no damage to lanyards, carabiners, attachment rings or belts.
check-marks-no.png
  • Don't use tools without attaching them to your work belt when working at height.
  • Don't use and fix damaged tools.
  • Don't exceed maximum weight of 2.3kg for individual tools that a worker can attach to their belt.

Safety (pictures)

User must be trained to perform work at heights pursuant to the national legislation.

User must use the prescribed personal protective equipment.

Working range at heights is the radius of two metres from the point of attachment on the user. No other person or equipment is permitted within that range due to the possibility of damage caused by a falling tool.

Please check the tools regularly and always before each use.

After any fall of a tool, check the rope and the tool. If necessary, replace the tool and/or rope.

The maximum weight of each tool defined by Unior as safe tool for work at heights attached to a work belt amounts to 2.3kg.

The total weight of tools that can be attached to a user's work belt should not exceed 10% of the user's weight.

Attachment ropes should not be shortened, reworked etc. If a rope is damaged or destroyed, do not use the tools.

During work, do not unfasten or detach tools from yourself.

When changing (switching) tools, it is recommended to observe the procedure of replacement described in the Unior d.d. catalogue (tools are attached throughout the replacement with one carabiner or the replacement is made at a so-called safe place).

Do not drop or throw tools deliberately, since this may result in a spring effect and unforeseen consequences.

Tools on a rope should not be wound, since that may lead to unforeseen consequences.

User selects Unior attachment elements depending on the purpose of use and with respect to the weight of tools (tool weight is indicated on a tool).

Tracking manufacture code and final control code are indicated on each tool.

Questions & Answers

  • Can we use a tool for working at height as a normal tool?
    A tool for working at height has the same usability as a normal tool, except that a non-removable riveted metal buckle is added to this tool.
  • Does the stated weight per tool for safe work at height also include the weight of the metal ring?
    The weight of the tool marked on the tool, included also weight of metal ring
  • YÜKSEK ETKİLİ ÇÖZÜMLER

    Yüksekte çalışmak yüksek risk içerir, bu yüzden hiçbir şey şansa bırakılamaz. Yüksek kaliteli el aletlerinin eş anlamlısı olan Unior, tehlikeli düşmeleri önlemek için yükseklikte çalışmak için özellikle uyarlanmış bir dizi araç sunar.
  • YÜKSEK KALİTEDE GÜVENLİ ÇALIŞMA İÇİN YÜKSEK KALİTE ARAÇLARI

    Tools for working at heights are standard tools equipped with attachment points. secured tools significantly increase job safety.
  • Yüksek hassasiyet

    Unior’un yükseklikte çalışma aletleri, araçların temel işlevlerini, ergonomisini ve kullanışlılığını korumak veya bunları mümkün olan en küçük ölçüde azaltmak için tasarlanmıştır.