Kombine penseler, yüksekliklerde güvenli çalışma için
More About Product
Profiller
Product features
- malzeme: özel alet çeliği
- sıcak dövme, tamamen sertleştirilmiş ve temperlenmiş
- kesici ağızlı endüksiyonla sertleştirilmiş
- cilalı başlık
- yüzey bitirme: ISO 1456:2009 uyarınca krom kaplı
- ağır hizmet tipi iki bileşenli saplar
- ISO 5746 standardına göre yapılmıştır
Avantajları:
- En yüksek güvenlik seviyesini sağlamak için perçinlenmiş metal halka yalnızca plastik kollara monte edilmez, aynı zamanda alet kolunun metal kısmına tutturulur.
- çıkarılamayan perçinli metal halka
- takım ağırlığı her takımın üzerinde işaretlenmiştir
- aletlerin üzerindeki halkalar 2 karabinayı alacak kadar büyüktür
- Unior’un yükseklikte çalışma aletleri, araçların temel işlevlerini, ergonomisini ve kullanışlılığını korumak veya bunları mümkün olan en küçük ölçüde azaltmak için tasarlanmıştır.
 |  |  |  |
|---|---|---|---|
| 626958 | 160 | 1,6 | 2,0 |
| 626959 | 180 | 1,8 | 2,5 |
Kullanım (pictures)
The carabiner on the lanyard is attached to the ring on the tool. The rings on the tools are large enough to accept 2 carabiners.
The carabiner on the lanyard has to be protected against opening using a lock ring.
Before removing the tool from the belt, unscrew the lock ring on the carabiner on the belt.
Open the carabiner on the belt and remove the tool, which is attached to a lanyard, from the carabiner on the belt. The tool is now ready for use.
Correct attachment of the tool to the lanyard. Return the tool to the belt following the steps in reverse order.
Using the socket remover (Article 1111) depress the pin in the hole while removing the socket from the square drive of the ratchet and then switch the socket or extension.
Safety tips
- Pliers should be oiled regularly. A drop of oil at the hinge will lengthen the tool life and assure easy operation.
- When cutting wire with pliers, you should always wear glasses or goggles.
- Handles are provided for comfort. They are not intended to give user any degree of protection against electric shocks and should never be used on live electric circuits.
- Don't use pliers for cutting hardened wire, unless specifically manufactured for this purpose.
- Don't expose pliers to excessive heat. This may ruin the tool.
- Don't use pliers as a hammer.
- Don't hammer on the handles. They may crack or break.
- Don't extend the length of plier handles to secure greater leverage.
- Don't use pliers on nuts or bolts. A wrench will do a better job and with less risk of damage to the fastener.
Safety (pictures)
User must be trained to perform work at heights pursuant to the national legislation.
User must use the prescribed personal protective equipment.
Working range at heights is the radius of two metres from the point of attachment on the user. No other person or equipment is permitted within that range due to the possibility of damage caused by a falling tool.
Please check the tools regularly and always before each use.
After any fall of a tool, check the rope and the tool. If necessary, replace the tool and/or rope.
The maximum weight of each tool defined by Unior as safe tool for work at heights attached to a work belt amounts to 2.3kg.
The total weight of tools that can be attached to a user's work belt should not exceed 10% of the user's weight.
Attachment ropes should not be shortened, reworked etc. If a rope is damaged or destroyed, do not use the tools.
During work, do not unfasten or detach tools from yourself.
When changing (switching) tools, it is recommended to observe the procedure of replacement described in the Unior d.d. catalogue (tools are attached throughout the replacement with one carabiner or the replacement is made at a so-called safe place).
Do not drop or throw tools deliberately, since this may result in a spring effect and unforeseen consequences.
Tools on a rope should not be wound, since that may lead to unforeseen consequences.
User selects Unior attachment elements depending on the purpose of use and with respect to the weight of tools (tool weight is indicated on a tool).
Tracking manufacture code and final control code are indicated on each tool.
Questions & Answers
-
Can we use a tool for working at height as a normal tool?A tool for working at height has the same usability as a normal tool, except that a non-removable riveted metal buckle is added to this tool.
-
Does the stated weight per tool for safe work at height also include the weight of the metal ring?The weight of the tool marked on the tool, included also weight of metal ring
YÜKSEK ETKİLİ ÇÖZÜMLER
Yüksekte çalışmak yüksek risk içerir, bu yüzden hiçbir şey şansa bırakılamaz. Yüksek kaliteli el aletlerinin eş anlamlısı olan Unior, tehlikeli düşmeleri önlemek için yükseklikte çalışmak için özellikle uyarlanmış bir dizi araç sunar.YÜKSEK KALİTEDE GÜVENLİ ÇALIŞMA İÇİN YÜKSEK KALİTE ARAÇLARI
Tools for working at heights are standard tools equipped with attachment points. secured tools significantly increase job safety.Yüksek hassasiyet
Unior’un yükseklikte çalışma aletleri, araçların temel işlevlerini, ergonomisini ve kullanışlılığını korumak veya bunları mümkün olan en küçük ölçüde azaltmak için tasarlanmıştır.