Clesti tais lateral pentru conditii grele, pentru lucrul in siguranta la inaltime

#tif#
466/1VDP-H

Foaie de calcul tabelar

pdfClesti tais lateral pentru conditii grele, pentru lucrul in siguranta la inaltime - 466/1VDP-H

pdf Certificate

pdf Certificate of compliance

Mai multe despre produs

Profile

Lifetime warranty

Caracteristicile produsului

  • material:compozitie speciala pentru calire revenire
  • tratat complet
  • partile taietoare tratate prin inductie
  • finisare:cromat in conformitate cu standardul EN12540
  • in conformitate cu standardul ISO 5749 si EN IEC 60900

Avantaje:

  • manerele izolate cu doua straturi de culori diferite care permit o protectie suplimentara
  • Uneltele pentru lucrul la înălțimi ale lui Unior au fost concepute pentru a păstra funcțiile de bază, ergonomia și utilitatea uneltelor sau pentru a le reduce cât mai puțin posibil.
  • Greutatea uneltei este marcata pe fiecare in parte
Important
  • daca al doilea strat devine vizibil inlocuiti scula VDE cu una noua
  • Unealta izolata nu este destinat utilizării cu carabiniere, ci cu un șnur cu un cablu.
#title#
coddimLenghtWidthThicknessAdditionsl lenghtGreutate
626964180215281121351
cutting capacity (10N=1kg)
coddimSarma 2150 N/mm²CuSn6 diametrul Max. (mm)Sarma max.650 N/mm² diametrul Max. (mm)
6269641801,83,0
* Imaginea produsului este simbolica.Toate dimensiunile sunt exprimate în mm,greutatea în grame.

Utilizare (Imagini)

The carabiner on the lanyard is attached to the ring on the tool. The rings on the tools are large enough to accept 2 carabiners.

The carabiner on the lanyard is attached to the ring on the tool. The rings on the tools are large enough to accept 2 carabiners.

The carabiner on the lanyard has to be protected against opening using a lock ring.

The carabiner on the lanyard has to be protected against opening using a lock ring.

Before removing the tool from the belt, unscrew the lock ring on the carabiner on the belt.

Before removing the tool from the belt, unscrew the lock ring on the carabiner on the belt.

Open the carabiner on the belt and remove the tool, which is attached to a lanyard, from the carabiner on the belt. The tool is now ready for use.

Open the carabiner on the belt and remove the tool, which is attached to a lanyard, from the carabiner on the belt. The tool is now ready for use.

Correct attachment of the tool to the lanyard. Return the tool to the belt following the steps in reverse order.

Correct attachment of the tool to the lanyard. Return the tool to the belt following the steps in reverse order.

Using the socket remover (Article 1111) depress the pin in the hole while removing the socket from the square drive of the ratchet and then switch the socket or extension.

Using the socket remover (Article 1111) depress the pin in the hole while removing the socket from the square drive of the ratchet and then switch the socket or extension.

Safety tips

check-mark-yes.png
  • Always change tools in secure areas where there is no risk of falling tools.
  • Always use tools with Unior carabiners and never use carabiners with a diameter less than 6mm.
  • Tools being used at height should regularly be checked for damage and that there is no damage to lanyards, carabiners, attachment rings or belts.
check-marks-no.png
  • Don't use tools without attaching them to your work belt when working at height.
  • Don't use and fix damaged tools.
  • Don't exceed maximum weight of 2.3kg for individual tools that a worker can attach to their belt.

Safety (Imagini)

User must be trained to perform work at heights pursuant to the national legislation.

User must be trained to perform work at heights pursuant to the national legislation.

User must use the prescribed personal protective equipment.

User must use the prescribed personal protective equipment.

Working range at heights is the radius of two metres from the point of attachment on the user. No other person or equipment is permitted within that range due to the possibility of damage caused by a falling tool.

Working range at heights is the radius of two metres from the point of attachment on the user. No other person or equipment is permitted within that range due to the possibility of damage caused by a falling tool.

Please check the tools regularly and always before each use.

Please check the tools regularly and always before each use.

After any fall of a tool, check the rope and the tool. If necessary, replace the tool and/or rope.

After any fall of a tool, check the rope and the tool. If necessary, replace the tool and/or rope.

The maximum weight of each tool defined by Unior as safe tool for work at heights attached to a work belt amounts to 2.3kg.

The maximum weight of each tool defined by Unior as safe tool for work at heights attached to a work belt amounts to 2.3kg.

The total weight of tools that can be attached to a user's work belt should not exceed 10% of the user's weight.

The total weight of tools that can be attached to a user's work belt should not exceed 10% of the user's weight.

Attachment ropes should not be shortened, reworked etc. If a rope is damaged or destroyed, do not use the tools.

Attachment ropes should not be shortened, reworked etc. If a rope is damaged or destroyed, do not use the tools.

During work, do not unfasten or detach tools from yourself.

During work, do not unfasten or detach tools from yourself.

When changing (switching) tools, it is recommended to observe the procedure of replacement described in the Unior d.d. catalogue (tools are attached throughout the replacement with one carabiner or the replacement is made at a so-called safe place).

When changing (switching) tools, it is recommended to observe the procedure of replacement described in the Unior d.d. catalogue (tools are attached throughout the replacement with one carabiner or the replacement is made at a so-called safe place).

Do not drop or throw tools deliberately, since this may result in a spring effect and unforeseen consequences.

Do not drop or throw tools deliberately, since this may result in a spring effect and unforeseen consequences.

Tools on a rope should not be wound, since that may lead to unforeseen consequences.

Tools on a rope should not be wound, since that may lead to unforeseen consequences.

User selects Unior attachment elements depending on the purpose of use and with respect to the weight of tools (tool weight is indicated on a tool).

User selects Unior attachment elements depending on the purpose of use and with respect to the weight of tools (tool weight is indicated on a tool).

Tracking manufacture code and final control code are indicated on each tool.

Tracking manufacture code and final control code are indicated on each tool.

Questions & Answers

  • Uneltele izolate certificate sunt realizate printr-o procedură diferită de cea a instrumentelor izolate necertificate?
    Instrumentele sunt realizate în conformitate cu aceeași procedură.
  • Instrumentele izolate (VDE) sunt considerate echipamente individuale de protecție (EIP)?
    În conformitate cu reglementările UE, instrumentele VDE nu sunt considerate EIP.
  • Este posibil să lucrați cu clești izolați sub tensiune electrică?
    Da, dar numai de către profesioniștii care respectă cerințele de siguranță și folosesc echipamente individuale de protecție suplimentare.
  • Instrumentele VDE sunt testate în producția de serie doar pe esantioane?
    Testul de înaltă tensiune (la 10kV) se efectuează complet pe fiecare instrument. Alte teste sunt efectuate în conformitate cu standardul EN60900.

  • Soluții foarte eficiente

    Lucrul la înălțimi implică un nivel ridicat de risc, deci nimic nu poate fi lăsat la întâmplare. Unior - un sinonim pentru sculele de mână de înaltă calitate, prezintă o gamă de unelte special adaptate pentru a lucra la înălțimi, pentru a evita

  • Instrumente de înaltă calitate pentru o muncă sigură la înălțime

    Tools for working at heights are standard tools equipped with attachment points. secured tools significantly increase job safety.

  • Inalta precizie

    Uneltele pentru lucrul la înălțimi ale lui Unior au fost concepute pentru a păstra funcțiile de bază, ergonomia și utilitatea uneltelor sau pentru a le reduce cât mai puțin posibil.