Multifunctionele elektricienstang, voor veilig werken op hoogte
Meer over dit product
Profielen
Producteigenschappen
- materiaal: premium plus carbonstaal
- gesmeed, volledig gehard en getemperd
- snijkanten inductief gehard
- kop gepolijst
- afwerking oppervlak: verchroomd volgens EN12540-norm
- dubbel-component handvaten voor zeer intensief gebruik
Voordelen:
- In order to ensure the highest level of safety, the riveted metal ring is not mounted only through the plastic handles but is attached through the metal part of the tool handle.
- non-removable riveted metal ring
- tool weight is marked on each tool
- the rings on the tools are large enough to accept 2 carabiners
- Unior’s tools for working at heights have been designed to preserve the tools’ basic functions, ergonomics and utility, or to reduce them to the smallest possible extent.
- 6 verschillende functies
- meertandige bek
- ergonomisch gevormd handvat
- extra sterke grip - het ontwerp en de vorm van de handgrepen geven de hand meer invloed tijdens het gebruik, waardoor er een veiligere en stabielere krachtoverbrenging mogelijk is.
- hoge duurzaamheid
- Meertandige bek voorkomt glijden en zorgt voor een betere grip van kabels, draden etc.
Gebruik:
- De onderkant van de bek is bestemd voor het grijpen van voorwerpen met gevoelige oppervlakken.
- De tangen kunnen gebruikt worden voor het plooien van kabelschoenklemmen.
- Het strippen van isolatie van Ø 2,2 mm tot Ø 3,0 mm.
- Het strippen van isolatie van Ø 3,5 mm tot Ø 4,0 mm.
- Het knippen van kabels van Ø 2,2 mm tot 4,0 mm.
- Kabelschoenklemmen plooien tot Ø 4,0 mm
 |  |  |  |
|---|---|---|---|
| 626259 | 160 | 1,6 | 2,0 |
Gebruik (foto's)
The carabiner on the lanyard is attached to the ring on the tool. The rings on the tools are large enough to accept 2 carabiners.
The carabiner on the lanyard has to be protected against opening using a lock ring.
Before removing the tool from the belt, unscrew the lock ring on the carabiner on the belt.
Open the carabiner on the belt and remove the tool, which is attached to a lanyard, from the carabiner on the belt. The tool is now ready for use.
Correct attachment of the tool to the lanyard. Return the tool to the belt following the steps in reverse order.
Using the socket remover (Article 1111) depress the pin in the hole while removing the socket from the square drive of the ratchet and then switch the socket or extension.
Veiligheidstips
- Always change tools in secure areas where there is no risk of falling tools.
- Always use tools with Unior carabiners and never use carabiners with a diameter less than 6mm.
- Tools being used at height should regularly be checked for damage and that there is no damage to lanyards, carabiners, attachment rings or belts.
- Don't use tools without attaching them to your work belt when working at height.
- Don't use and fix damaged tools.
- Don't exceed maximum weight of 2.3kg for individual tools that a worker can attach to their belt.
Veiligheid (foto's)
User must be trained to perform work at heights pursuant to the national legislation.
User must use the prescribed personal protective equipment.
Working range at heights is the radius of two metres from the point of attachment on the user. No other person or equipment is permitted within that range due to the possibility of damage caused by a falling tool.
Please check the tools regularly and always before each use.
After any fall of a tool, check the rope and the tool. If necessary, replace the tool and/or rope.
The maximum weight of each tool defined by Unior as safe tool for work at heights attached to a work belt amounts to 2.3kg.
The total weight of tools that can be attached to a user's work belt should not exceed 10% of the user's weight.
Attachment ropes should not be shortened, reworked etc. If a rope is damaged or destroyed, do not use the tools.
During work, do not unfasten or detach tools from yourself.
When changing (switching) tools, it is recommended to observe the procedure of replacement described in the Unior d.d. catalogue (tools are attached throughout the replacement with one carabiner or the replacement is made at a so-called safe place).
Do not drop or throw tools deliberately, since this may result in a spring effect and unforeseen consequences.
Tools on a rope should not be wound, since that may lead to unforeseen consequences.
User selects Unior attachment elements depending on the purpose of use and with respect to the weight of tools (tool weight is indicated on a tool).
Tracking manufacture code and final control code are indicated on each tool.
Vraag en Antwoord
-
Can we use a tool for working at height as a normal tool?A tool for working at height has the same usability as a normal tool, except that a non-removable riveted metal buckle is added to this tool.
-
Does the stated weight per tool for safe work at height also include the weight of the metal ring?The weight of the tool marked on the tool, included also weight of metal ring
ZEER EFFICIENTE OPLOSSINGEN
Werken op hoogte brengt grote risico's met zich mee, dus niets mag aan het toeval worden overgelaten. Unior – een synoniem voor handgereedschap van hoge kwaliteit, presenteert een reeks gereedschappen die speciaal zijn aangepast voor het werken op hoogte om gevaarlijke valpartijen te voorkomen.HOOGWAARDIG GEREEDSCHAP VOOR VEILIG WERKEN OP HOOGTE
Gereedschappen voor het werken op hoogte zijn standaard gereedschappen voorzien van bevestigingspunten. Beveiligde gereedschappen verhogen de arbeidsveiligheid aanzienlijk.HOGE PRECISIE
Unior-gereedschappen voor werken op hoogte zijn zo ontworpen dat de basisfuncties van het gereedschap, de ergonomie en de bruikbaarheid behouden blijven of slechts minimaal beperkt worden waar nodig.