重型斜嘴钳

#tif#
466/1VDP-H

数据表

pdf重型斜嘴钳 - 466/1VDP-H

pdf Certificate

pdf Certificate of compliance

更多关于产品

配置文件

Lifetime warranty

产品属性

  • 材料：特种工具钢
  • 落锻，完全淬火与回火
  • 切削刃感应淬火
  • 表面处理：依据ISO 1456:2009进行镀铬处理
  • 根据ISO 5749标准和EN IEC 60900生产

优势：

  • 通过双层涂料绝缘的把手 — 提供额外安全的双色绝缘保护
  • Unior用于高空作业的工具被设计成保留工具的基本功能、人体工程学和效用，或者尽可能减少它们的附加功能。
  • 每个工具上都标有工具重量
重要事项！
  • 如果第二层显露出来，请立即更换您的VDE工具
  • 绝缘工具不是为与钩一起使用而设计的，而是与带有绳索的系绳一起使用的。
#title#
编码尺寸LenghtWidthThicknessAdditionsl lenght重量
626964180215281121351
cutting capacity (10N=1kg)
编码尺寸Wire max.2150 N/mm² Max. diameter (mm)Wire max.650 N/mm² Max. diameter (mm)
6269641801,83,0
* Images of products are symbolic. All dimensions are in mm, and weight in grams. All listed dimensions may vary in tolerance.

使用 (图片)

The carabiner on the lanyard is attached to the ring on the tool. The rings on the tools are large enough to accept 2 carabiners.

The carabiner on the lanyard is attached to the ring on the tool. The rings on the tools are large enough to accept 2 carabiners.

The carabiner on the lanyard has to be protected against opening using a lock ring.

The carabiner on the lanyard has to be protected against opening using a lock ring.

Before removing the tool from the belt, unscrew the lock ring on the carabiner on the belt.

Before removing the tool from the belt, unscrew the lock ring on the carabiner on the belt.

Open the carabiner on the belt and remove the tool, which is attached to a lanyard, from the carabiner on the belt. The tool is now ready for use.

Open the carabiner on the belt and remove the tool, which is attached to a lanyard, from the carabiner on the belt. The tool is now ready for use.

Correct attachment of the tool to the lanyard. Return the tool to the belt following the steps in reverse order.

Correct attachment of the tool to the lanyard. Return the tool to the belt following the steps in reverse order.

Using the socket remover (Article 1111) depress the pin in the hole while removing the socket from the square drive of the ratchet and then switch the socket or extension.

Using the socket remover (Article 1111) depress the pin in the hole while removing the socket from the square drive of the ratchet and then switch the socket or extension.

Safety tips

check-mark-yes.png
  • Always change tools in secure areas where there is no risk of falling tools.
  • Always use tools with Unior carabiners and never use carabiners with a diameter less than 6mm.
  • Tools being used at height should regularly be checked for damage and that there is no damage to lanyards, carabiners, attachment rings or belts.
check-marks-no.png
  • Don't use tools without attaching them to your work belt when working at height.
  • Don't use and fix damaged tools.
  • Don't exceed maximum weight of 2.3kg for individual tools that a worker can attach to their belt.

Safety (图片)

User must be trained to perform work at heights pursuant to the national legislation.

User must be trained to perform work at heights pursuant to the national legislation.

User must use the prescribed personal protective equipment.

User must use the prescribed personal protective equipment.

Working range at heights is the radius of two metres from the point of attachment on the user. No other person or equipment is permitted within that range due to the possibility of damage caused by a falling tool.

Working range at heights is the radius of two metres from the point of attachment on the user. No other person or equipment is permitted within that range due to the possibility of damage caused by a falling tool.

Please check the tools regularly and always before each use.

Please check the tools regularly and always before each use.

After any fall of a tool, check the rope and the tool. If necessary, replace the tool and/or rope.

After any fall of a tool, check the rope and the tool. If necessary, replace the tool and/or rope.

The maximum weight of each tool defined by Unior as safe tool for work at heights attached to a work belt amounts to 2.3kg.

The maximum weight of each tool defined by Unior as safe tool for work at heights attached to a work belt amounts to 2.3kg.

The total weight of tools that can be attached to a user's work belt should not exceed 10% of the user's weight.

The total weight of tools that can be attached to a user's work belt should not exceed 10% of the user's weight.

Attachment ropes should not be shortened, reworked etc. If a rope is damaged or destroyed, do not use the tools.

Attachment ropes should not be shortened, reworked etc. If a rope is damaged or destroyed, do not use the tools.

During work, do not unfasten or detach tools from yourself.

During work, do not unfasten or detach tools from yourself.

When changing (switching) tools, it is recommended to observe the procedure of replacement described in the Unior d.d. catalogue (tools are attached throughout the replacement with one carabiner or the replacement is made at a so-called safe place).

When changing (switching) tools, it is recommended to observe the procedure of replacement described in the Unior d.d. catalogue (tools are attached throughout the replacement with one carabiner or the replacement is made at a so-called safe place).

Do not drop or throw tools deliberately, since this may result in a spring effect and unforeseen consequences.

Do not drop or throw tools deliberately, since this may result in a spring effect and unforeseen consequences.

Tools on a rope should not be wound, since that may lead to unforeseen consequences.

Tools on a rope should not be wound, since that may lead to unforeseen consequences.

User selects Unior attachment elements depending on the purpose of use and with respect to the weight of tools (tool weight is indicated on a tool).

User selects Unior attachment elements depending on the purpose of use and with respect to the weight of tools (tool weight is indicated on a tool).

Tracking manufacture code and final control code are indicated on each tool.

Tracking manufacture code and final control code are indicated on each tool.

Questions & Answers

  • Are certified insulated tools made through a different procedure than non-certified insulated tools?
    The tools are made according to the same procedure.
  • Are insulated (VDE) tools considered as personal protective equipment (PPE)?
    According to EU regulations, VDE tools are not considered as PPE.
  • Is it possible to work with insulated pliers under electrical voltage?
    Yes, but only by professionals who follow safety requirements and use additional personal protective equipment.
  • Are the VDE tools only being sampled in series production?
    The high voltage test (at 10kV) is performed fully on each tool. Other tests are performed in accordance with the EN60900 standard.

  • 高效的解决方案

    在高空工作需要冒很大的风险，所以不能靠运气。Unior——高品质手工工具的同义词，推出了一系列专门适用于高空作业的工具。

  • 高质量的工具，安全工作的高度

    Tools for working at heights are standard tools equipped with attachment points. secured tools significantly increase job safety.

  • 高精度

    Unior高空工具的设计，保留工具的基本功能、人体工程学和效用，或者尽可能缩减它们的延展功能。