产品属性

  • 双向棘轮头
  • 扭力应用:单向,但始终根据扭力扳手把手规定方向施力
  • 棘轮可顺时针或逆时针运行
  • 用于紧固左旋或右旋螺纹
  • 达到固定扭力时出现明确无误的信号
  • 重新校准间隔的默认范围是使用12个月或5000次之后!
  • 根据ISO 6789标准生产
  • 双标度,Nm和Kgm

重要事项!

  • 请勿使用扭力扳手进行拧松操作!
  • 务必根据重要提示贴纸上所示的方向进行扭力紧固!贴纸所示为正确紧固方向!
  • 扭力扳手的默认校准周期为12个月或最终用户购买之日起5000次测量后
  • 使用完毕后,务必将测量仪器归零。
  • 达到要求的扭力时,请勿继续紧固。
  • 如未遵守手册说明,可导致扭力扳手损坏。
#title#
编码Sign SQ 4-point profileTorque in NmLenght重量
6154851/4"2 - 24270686
6154863/8"5 - 1103601100
6154871/2"28 - 2104651680
6154881/2"35 - 3506402930
6154893/4"70 - 5608405600
6154903/4"140 - 70010708200
6154911"140 - 98012208800
* Images of products are symbolic. All dimensions are in mm, and weight in grams. All listed dimensions may vary in tolerance.

使用 (图片)

拧松底部螺栓、螺钉,调整扭矩

调整指定扭矩值

旋转拧紧底部螺丝,固定扭矩

根据扭矩指示说明调整并开始拧紧,当您听到音频信号(滴答声),达到指定的扭矩,停止拧紧。

Warning! Never loosen screw marked red. In the event of unscrewing, your warranty will be void.

使用 (视频)

Safety tips

check-mark-yes.png
  • Only an authorised person in a certificated service centre can perform technical maintenance.
  • Tools should always be serviced and calibrated by a certified service engineer.
  • Tool should only be used for precise tightening as specified in the instruction manual.
  • Check instruction manual on how to read the value scale on the tool properly.
  • Stop tightening after hearing a feedback from the tool.
  • Use only sockets with the same square drive.
  • Always return the value on the scale back to 0 after usage and before storing.

Safety (图片)

Don't store a tool that is dusty and not cleaned after use.

Always check that tool has a valid certificate and always follow the calibration interval specified in the instruction manual for your tool.

When applying torque, always apply it with even and constant pressure.

The torque wrench must always be kept protected in its original packaging when not used.

Photo (图片)

  • 测量精度

    卷尺、带有过载保护的扭力扳手、游标卡尺(包括数显游标卡尺)、水平仪、曲尺、泥工水平仪和测隙规都是精确测量仪器,没有这些仪器则无法顺利规划和执行工作。
  • 安全测试用途

    测量工具精确且易于使用——既可作为普通卷尺对各种不同变量的常规测量,还可用于特定工种对螺纹等的测量。
  • 多版本

    Unior精度工具通用款以及带有计时器或其他功能的顶尖数字类型产品,所有工具的设计和生产均符合当前国际通用标准。